Handyman · Troubleshooting

Drawer Not Closing Properly? How to Fix or Replace the Runners

By SG QuickFixLast updated 7 min read

Quick answer

A drawer usually won't close properly because something is jammed behind it, a runner has come off its track or loosened, or a ball-bearing runner's retainer has slipped. Empty it, clear the back and re-seat it first. Bent runners or missing bearings need replacing. In Singapore, SG QuickFix adjusts a drawer from $50.

SG QuickFix pricesTap to WhatsApp

Drawer adjustmentFrom $50
Drawer runner replacement+ runnerFrom $60
Minor furniture repairFrom $60
Wardrobe door alignmentFrom $60

Current SG QuickFix starting prices. Final price confirmed before work begins.

Not sure? WhatsApp us a photo or 10-second video and we'll tell you if it's a DIY fix.

WhatsApp us
Kitchen drawer in a Singapore HDB flat sitting crooked and not closing fully against the cabinet

Why won't my drawer close properly?

Most drawers that won't close are blocked by contents, off their runners, held by loose screws, or running on a damaged runner.

What the symptom usually means
SymptomLikely causeFirst check
Stops a few centimetres shortAn item caught behind or above the drawerPull the drawer out and look behind it
Drops or tilts when pulled outRunner screws pulled out of the chipboard, or the drawer is off its trackLook at the screws on the cabinet side
Won't go back in after removalBall-bearing retainer has slid to the backLook for the ball cage inside the cabinet runner
Grinds or feels roughDirt in the runner, a bent section or lost bearingsSlide it slowly and listen
Rubs along the sidesSwollen drawer box or cabinet panelCheck for swollen edges, especially near the sink
Springs back open or stops shortPush-to-open or soft-close unit needs adjustingSee the soft-close section below

In Singapore, the Meteorological Service Singapore puts mean relative humidity at around 82%. Particleboard and MDF edges absorb that moisture, especially under a leaking kitchen sink, so a swollen box rubs even on a good runner. It is the same problem as a door swollen due to humidity.

Most of these faults need a drawer and cabinet repair, not new furniture.

Kitchen drawer in an HDB flat pulled out to show a side-mount ball-bearing runner

Which type of drawer runner do I have?

Most home drawers run on side-mount ball-bearing, bottom-mount roller, concealed undermount or metal box-system runners. Pull the drawer out and look at its sides and underside.

Common drawer runner types
Runner typeHow to recognise itCommon fault
Side-mount ball-bearingThree telescoping steel sections on each side, small ball cages, a lever to release the drawerSlipped retainer, bent section, lost balls
Bottom-mount rollerWhite or grey rails under the drawer's bottom edges, nylon wheels; the drawer opens about three-quarters and often pulls itself shutCracked wheel, drawer jumping off the track
Concealed undermountRunners hidden under the drawer, with release clips at the front underneathClips not engaged, front out of line
Metal box systemMetal drawer sides with built-in runners and screw coversFront out of line or tilted

In most HDB kitchens, drawers are particleboard boxes on side-mount ball-bearing or bottom-mount roller runners. Undermount and box-system drawers usually have small adjusters (screws, dials or tabs) for height, side position and tilt. On IKEA MAXIMERA drawers they sit behind the side covers, and IKEA's MAXIMERA guide says to start with the bottom drawer.

How do I fix a drawer that won't close?

Empty the drawer, take it out, clear the cabinet, then tighten the screws and reset the runners before refitting it level.

  1. Empty the drawer so it is light and nothing falls behind it.
  2. Pull it fully out, then press the release levers, squeeze the clips underneath, or lift it off the rollers.
  3. Clear anything behind the drawer and wipe dust and grit from both runners.
  4. Tighten loose runner screws by hand. If a screw spins, stop: the hole is stripped and needs repairing first.
  5. On ball-bearing runners, push the ball cage in the cabinet section fully forward.
  6. Refit the drawer level, engaging both sides together, and push it in slowly.
  7. Test it with its normal load; if it still binds, check the runners are parallel.

If a steel runner still feels rough after cleaning, one major runner maker recommends a little grease on the ball tracks. Spray oil loosens grime but doesn't last and collects dust.

Why does my drawer keep opening, or my soft-close drawer stop short?

A drawer that keeps opening is usually a push-to-open unit set with the wrong front gap, or runners sloping towards you.

Push-to-open drawers spring out when you press the front. They need an exact gap between the front and the cabinet, which one major maker sets at 2.5 mm. Rubber bumpers or dirt in the catch stop them working. Reset the gap with the adjusting screw and remove any added bumpers.

If a normal drawer rolls open by itself, the cabinet or its runners are probably sloping towards you; check with a spirit level. Freestanding furniture levels with its feet or packers; a built-in kitchen cabinet usually needs the runners re-set level.

A soft-close drawer that stops short is often blocked, or its runners aren't parallel or level. A very light drawer may also need a firmer push to set the damper. If the damper no longer slows the drawer at all, it has worn out, and on most runners that means a new pair.

When should drawer runners be replaced, and how do I measure them?

Replace both runners when a steel section is bent, balls are missing, a wheel is cracked, rust has set in, or the soft-close has died.

A drawer box with split joints or a dropped, swollen bottom needs repair first, or new runners will still bind. Always replace runners as a pair with the same model.

How do I measure a replacement runner?

Match all four:

  • Length: measure the drawer box side from front to back, and check the cabinet is at least that deep inside. Runners usually come in 50 mm steps, from about 250 mm to 700 mm.
  • Side clearance: subtract the drawer width from the opening width, then halve it. Ball-bearing side-mounts typically need 12.7 mm each side; roller runners about 12.5 mm.
  • Mount type: side, bottom or undermount. Undermount runners need the drawer built to their exact width.
  • Load: ratings are per pair and include the drawer itself. Roller runners are often rated at 25 to 30 kg; standard ball-bearing runners at about 34 to 45 kg.

Take the old runner to the shop, or photograph it next to a tape measure. If the old screw holes are stripped, fill them with glued hardwood dowel, let it set, then drive the screws back through the runner's own holes. Don't shift the runner, or it sits out of line with the other side.

Old drawer runner laid beside a tape measure to check its length before buying a replacement

How much does drawer repair cost in Singapore?

SG QuickFix adjusts a drawer from $50 and replaces drawer runners from $60, plus the runners.

Drawer and cabinet jobs
JobWhen you need itSG QuickFix price
Drawer adjustmentOff its track, slipped retainer, loose screws, front or push-to-open out of lineFrom $50
Drawer runner replacementBent section, missing balls, cracked wheel, rust or a dead soft-closeFrom $60, plus the runners
Wardrobe door alignmentWardrobe doors that don't meet or won't shutFrom $60
Minor furniture repairSplit drawer box, dropped bottom or stripped screw holesFrom $60
Cabinet hinge adjustmentA kitchen cabinet door fouling the drawer belowFrom $50

The price rises with undermount or soft-close runners, several drawers, sourcing a matching runner, or a damaged box. Each job is priced separately. For an accurate price, send a photo of the runner with the drawer pulled out, and the drawer's length. For kitchen cabinet doors, see cabinet hinge adjustment, or the full handyman price list for Singapore.

DIY or call a professional
Safe to DIY if…Call a professional if…
Something is jammed behind the drawerA steel runner section is bent or balls have fallen out: a handyman replaces the pair
Runner screws are loose but the holes still gripScrew holes are stripped or the cabinet side has swollen
A ball-bearing retainer has slid to the backYou can't find a runner matching the length, clearance and mount type
A push-to-open front gap needs a small adjustmentThe drawer box joints have split or the bottom has dropped: a handyman repairs the box
Never stand on or pull out several drawers of an unanchored tall chestA tall chest or wardrobe wobbles or leans forward: have it anchored to the wall with an anti-tip kit

What happens when you WhatsApp us?

  1. 1WhatsApp us a photo or short video of the problem.
  2. 2We confirm the price before we come.
  3. 3A technician arrives at the agreed time.
  4. 4The job is done and you pay only the confirmed price.

Cabinet / Furniture

From $50

  • Hinge & runner replacement
  • Door realignment

Cabinet / Furniture FAQs

Related services

Serving Bedok, Pasir Ris, Punggol, Sengkang and Tampines and island-wide.

Sources & updates
  • Updated 1 Oct 2026: First published
Share:

Related guides

Still need help with cabinet / furniture?

WhatsApp us a photo and get a clear price before we come. Open 24 hours, island-wide.

WhatsApp us

This guide is general information for homes in Singapore. It is not professional, legal or safety advice for your specific situation. Electrical, gas and some plumbing work can be dangerous, and Singapore law requires certain jobs to be done by licensed workers. Any work you carry out yourself is at your own risk, and SG QuickFix accepts no responsibility for any loss, damage or injury arising from the use of this information. Prices shown are current starting prices, may change, and the final price is confirmed before any work begins. Rules and figures from HDB, PUB, EMA, SP Group and town councils were correct when last checked; please confirm with the relevant authority before acting.

With your permission, we use analytics cookies to measure visits and the results of our ads. Until you choose, we only take cookie-free measurements. See our Privacy Policy.